View LTL1NHTBH4JZLC_8963960.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL1NHTBH4JZLC spec no.: ds20-2013-0204effective date: 08/16/2013revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y features * lead (pb) free product C package dimensions part no. lens source color ltl1nhtbh 4jzlc white diffused ingan blue notes: 1. all dimensions are in millimeters (inches). 2. tolerance is ltl1nhtbh 4jzlc pa ge : 1 of 10 bns - od - c131/a4 protection circuit protection zener led
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a =25 parameter ma ximum rating unit power dissipation 68 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 6 0 ma dc forward current 20 ma operating temperature range - 4 0 to + 8 5 storage temperature range - 40 to + 100 lead soldering temperatu re [2.0mm(0.8") from body] 260 for 5 seconds part no. : ltl1nhtbh 4jzlc page : 2 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical / optical characteristics at t a =25 parameter symbol min. typ. max. unit test condition luminous in tensity i v 50 1 80 310 mcd i f = 5 ma note 1,4 viewing angle 2 1/2 - 80 - deg note 2 (fig.6) peak emission wavelength p - 468 - nm measurement @peak (fig.1) dominant wavelength d 460 475 nm note 3 spectral line half - width ? - 20 - nm forward voltage v f - 3.0 3.4 v i f = 5 ma reverse current i r - - 10 a v r = 5v note: 1. luminous intensity is measu red with a light sensor and filter combination that approximates the cie (commission international de l'ecla irage) eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. the iv guarantee should be added 15%. 5. reverse current is controlled by dice source. 6 . reverse voltage (v r ) condition is applied for ir test only. the device is not designed for reverse operation. part no. : ltl1nhtbh 4jzlc page : 3 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted) part no. : ltl1nhtbh 4jzlc p age : 4 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y packing spec 1000 , 500, 200 or 100 pcs per packing bag 10 packing bags per inner carton to tal 10000 pcs per inner carton 8 inner cartons per outer carton total 80000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing part no. : ltl1nhtbh 4jzlc page : 5 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y bin table specification luminous i ntensity unit : mcd @5 ma bin code min. max. c 50 65 d 65 85 e 85 110 f 110 140 g 140 180 h 180 240 j 240 310 note: tolerance of each bin limit is 15% domin an t wavelength unit : nm @5 ma bin code min. max. b07 460 465 b08 465 470 b09 470 475 note: tolerance of each bin limit is 1nm part no. : ltl1nhtbh 4jzlc page : 6 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).consult liteons sales in advance for information on applic ations in which exceptional reliability is required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safet y devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original packaging are used within three months. for extended storage out of their original packag ing, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. cleaning use alcohol - based cleaning solvents such as isopropyl alcohol to clean the leds if necessary. 4. lead formi ng & assembly during lead forming, the leads should be bent at a point at least 3 mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during as sembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 5. soldering when soldering, for lamp without stopper type and must be leave a minimum of 3 mm clearance from the base of the lens to the soldering point . to avoided t he epoxy climb up on lead frame and was impact to non - soldering problem, dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperature. recommended soldering co nditions : soldering iron wave soldering temperature soldering time 35 0c max. 3 sec. max. (one time only) pre - heat pre - heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 5 sec. max. note: excessive soldering t emperature and/or time might result in deformation of the led lens or catastrophic failure of the led. ir reflow is not suitable process for through hole type led lamp product. part no. : ltl1nhtbh 4jzlc page : 7 of 10 b ns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 6. drive method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circu it, in series with each led as shown in circuit a below. circuit model a circuit model b (a) recommended c ircuit (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those leds 7. esd (electrostatic discharge) static electricity or power surge will damage the led. suggestions to preve nt esd damage: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the s tatic charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing part no. : ltl1nhtbh 4jzlc page : 8 of 10 bns - od - c131/a4 led led
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y suggested checking list : trainin g and certification 1. everyone working in a static - safe area is esd - certified? 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 1. static - safe workstation or work - areas have esd signs? 2. all su rfaces and objects at all static - safe workstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mats grounding is good? personnel grounding 1. every person (including visitors) ha ndling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also present where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds items identified by eia - 471 labels on item or packaging? 2. all esds items completely inside properly closed static - shielding containers when not at static - safe workstation? 3. no static charge generators (e.g. plastics) inside shie lding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 1. audit result reported to entity esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records complete and on file? part no. : ltl1nhtbh 4jzlc page : 9 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 8 . reliability test classification test item test condition reference standard endurance test operation life (lt) ta = under room temperature if = per datasheet maximum drive current *test time = 1000 hrs mil - std - 750d:1026 (1995) mil - std - 883g:1005 (2006) high temperature/ high humidity storage (thb) ta = 60 c rh = 90% test time = 240hrs mil - std - 202g:103b (2002) jeita ed - 4701:100 103 (2001) high temperature storage ta = 105 5c test time = 1000 hrs mil - std - 750d:1031 (1995) mil - std - 883g:1008 (2006) jeita ed - 4701:200 201 (2001) low temperature storage ta= - 55 5c test time = 1000 hrs jeita ed - 4701: 200 202 (2001) environmental test temperature cycling 100c ~ 25c ~ - 40c ~ 25c 30 mins 5 mins 30 mins 5 mins 30 cycles mil - std - 750d:1051 (1995) mil - std - 883g:1010 (2006) jeita ed - 4701:100 105 (2001) jesd22 - a104c (2005) thermal shock 100 5c ~ - 30 5c 15 mins 15 mins 30 cycles (< 20 secs transfer) mil - std - 750d:1056 (1995) mil - std - 883g:1011 (2006) mil - std - 202g:107g (2002) jesd22 - a106b (2004) solder resistance (no pre - condition) t.sol = 260 5c dwell time = 10 1 sec mil - std - 750d:2031 (1995) jeita ed - 4701: 300 302 (2001) solderability (no pre - condition) t.sol = 245 5c dwell time = 5 0.5 sec mil - std - 750d:2026 (1995) mil - std - 883g:2003 (2006) mil - std - 202g:208h (2002) ipc/eia j - st d - 002 (2004) soldering iron (no pre - condition) t.sol = 350 5c dwell time = 3.5 0.5 sec mil - std - 202g:208h (2002) jeita ed - 4701: 300 302 (2001) 9. others the appearance and specifications of the product may be modified for improvement, w ithout prior notice. part no. : ltl1nhtbh 4jzlc page : 10 of 10 bns - od - c131/a4

▲Up To Search▲

Price & Availability of LTL1NHTBH4JZLC

	To Download LTL1NHTBH4JZLC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .